MODERNIZATION OF LABORATORY STAND OF ASYNHRONOUS ELECTRIC DRIVE RESEARCH

Authors

  • Yu. A. Krysan Zaporozhye National Technical University, Ukraine

DOI:

https://doi.org/10.15588/1607-6761-2014-1-8

Keywords:

stand, electromechanical, microprocessor relay, control system, starting rheostat, asynchronous electric motor

Abstract

The worked out stand is based on the basis of existed laboratory equipment for research of the different modes of asynchronous electric drive. For a management the modes of starting and braking with the Moeller microprocessor relay is used.
The offered solution of modernization allows simultaneously to investigate work of electromechanical control system, realized on classic to the relay – contact base of management, and system, realized on a modern microprocessor equipment, and also to conduct the necessary tuning of stand constituents and investigate the transient of current slip-ring induction motoring.
An equipment allows to put right and test the next modes: rheostat starting slip-ring induction motoring in the functions of time, reverses, dynamic braking.
The worked out course of laboratory works allows to conduct timing of switching of degrees of resistances and construction of electromechanical descriptions slip-ring induction motoring and also to design his work using the SimPowerSystems libraries of МATLAB Simulink package. Creation of program algorithm and its realization as a EASYSOFT program environment are performed. Verification of rightness of the program writing and tuning of all program elements parameters are done. It is shown that the removal of the real current is in the phase of rotor (by means of digital oscillograph) and it is don’t the design comparison of its results

Author Biography

Yu. A. Krysan, Zaporozhye National Technical University

Ph.D, Associate Professor

References

Совершенствование лабораторного практикума обучения студентов по направлению подготовки «Электромеханика» / [Бондаренко В. И., Орловский И. А., Пирожок А. В. и др.] // Электротехнические системы и комплексы. – Магнитогорск. – Вып. 20. – 2012. – С. 412–438.

Мастепан А. Г. Стенды для исследования основ электропривода / А. Г. Мастепан, С. Н. Лутай // Сборник научных трудов «Вестник НТУ «ХПИ» : Проблеми автоматизованого електроприводу. Теорія і практика. – № 36 – Вестник НТУ «ХПИ», 2013. – С. 509–510.

Разработка универсального стенда электропривода на основе элементной базы фирмы «SIEMENS» /[Квашин В. О., Наливайко А. М., Колесникова Г. В., Шульга А. А.] // Вестник НТУ ХПИ Проблемы автоматизированного электропривода. Теория и практика. – Харьков. – 2008. – C. 134–136.

Методичні вказівки до лабораторних робіт з дисципліни «Теорія електропривода» для студентів спеціальності 8.092203 – Електромеханічні системи автоматизації та електропривод денної форми навчання / Укл. : Бондаренко В. І., Крисан Ю. О., Васильєва Є. В. – Запоріжжя : ЗНТУ, 2010. – 16 с.

Бондаренко В. І. Основи електропривода : навчальний посібник / В. І. Бондаренко, Ю. О. Крисан. – Запоріжжя : ЗНТУ, 2013. – 402 с.

Андрющенко О. А. Электронные программируемые реле серий EASY и MFD-Titan. Учебное пособие для изучения реле и проектирования систем автоматизации на их основе / О. А. Андрющенко, В. А. Водичев. – Одесса : ДП «Моэллер Электрик», 2006. – 235 с.

Downloads

How to Cite

Krysan, Y. A. (2014). MODERNIZATION OF LABORATORY STAND OF ASYNHRONOUS ELECTRIC DRIVE RESEARCH. Electrical Engineering and Power Engineering, (1), 49–54. https://doi.org/10.15588/1607-6761-2014-1-8

Issue

No. 1 (2014): Electrical Engineering and Power Engineering

Section

Electrotechnics

License

Copyright (c) 2017 Yu. A. Krysan

Creative Commons License

This work is licensed under a Creative Commons Attribution 4.0 International License.

Creative Commons Licensing Notifications in the Copyright Notices

Authors who publish with this journal agree to the following terms:

  • Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under aCreative Commons Attribution License that allows others to share the work with an acknowledgement of the work's authorship and initial publication in this journal.

  • Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgement of its initial publication in this journal.

  • Authors are permitted and encouraged to post their work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published work.